Zhuo Yue Resources Sdn Bhd
21, Jalan Kenari,
Desa Ria,
11900 Bayan Lepas,
Penang, Malaysia.
+6012-4113737

+604-6433737
zypoh@zhuoyuercs.com
poh3737@yahoo.com

UV Bridges, UV Bridging Modules, Table Top UV Dryers & UV Kits

Previous 1 / 10 Next

UV Bridges, UV Bridging Modules, Table Top UV Dryers & UV Kits Natgraph UV Dryer


UV Bridges,
UV Bridging Modules,
Table Top UV Dryers & UV Kits

Natgraph manufacture a range of UV Bridges that has been developed from many years of experience gained in the production of over 200 systems to add a UV curing capability to an existing air dryer. These UV Bridges are designed to be easily fitted onto the inlet section of the dryer to cure the UV inks before the substrate enters the forced air section. These units have been designed for curing UV surface coatings applied to promotional, electronic, credit card, glass, display and telecommunications products. If there is a UV curable ink available for an application, Natgraph will have a solution. A further and very popular development is the UV Bridging Module, this is a 1m wide unit that has the UV Bridge lamphouse located on the top, this module is installed between the drying/cooling modules of the existing dryer. Table Top UV Dryers are compact and efficient units available in 2 sizes, with high power and a comprehensive specification. Natgraph also manufacture a range of UV Curing Kits for installation within existing printing units, dryers or reel to reel machines.

UV Bridges

The Natgraph range of UV Bridges has been designed to be installed on the inlet of an existing forced air dryer to provide a cost effective, efficient and cool UV drying capability to an existing dryer. Available with 1 or 2 lamps, in 8 standard curing widths from 70cm through to 215cm, all standard print formats can be processed.
 
The all aluminium lamphouse has high efficiency, fully focused anodised aluminium reflectors and a flat quartz infra red heat filter window fitted below the lamps, that isolates the lamp cooling air from the substrate. This filter reduces the effect of the infra red energy from the UV lamps, resulting in a much reduced ‘impact temperature’ on the substrate. In addition, all ozone produced by the lamp is extracted through a dedicated fan that is mounted either directly onto the end of the lamphouse, or as a separate unit, which can either be floor or wall mounted. Natgraph’s technology ensures that this UV system is probably the coolest available, reducing substrate shrinkage and thus ensuring consistent print registration.

UV Bridge Features
• Compact unit
• Quartz infra red filter
• Fault finding circuit
• Hour meters
• Ammeters
• Warning siren
• Seperate transformer cabinet
• Optional belt movement sensor system
• Available in 8 sizes

UV Bridging Modules
The Natgraph range of UV Bridging Modules has been designed to be installed within an existing forced air dryer to provide a cost effective, efficient and cool UV drying capability that extends the dryer by only 1m. Available with 1 or 2 lamps, in 8 standard curing widths from 70cm through to 215cm, all standard print formats can be processed.

These modules are only 1m wide, yet contain the transformers, control circuitry, extraction fan and vacuum system, with the UV lamphouse and light traps mounted on the top. On wheels and jacking feet for final location, these comprehensive units can easily be installed within the existing dryer, in the ideal location after the last heated air module and before the first cooling module.

This position allows the UV ink time to ‘flow’ and gases to come out of clear varnishes, thus producing a flat image.

UV Bridging Module Features
• Self contained system
• Compact unit
• Quartz infra red heat filters
• Vacuum hold-down under lamps
• Castors & jacking feet
• Internal extraction / cooling fan
• Internal transformers
• Fault finding circuit
• Hour meters
• Ammeters
• Warning siren
• Optional belt movement sensor system
• Available in 8 sizes

Table Top UV Dryers
The Natgraph Table Top UV Dryers have been developed for smaller print formats and are based on our proven technology ensuring the highest quality and efficiency. These dryers utilise an ozone free medium pressure mercury vapour lamp, which provides high power curing of 131 watts per cm, this being without the need for extraction. All the control gear, cooling fans, motors etc contained in the extremely compact all steel construction make these units ideal for any situation.
These units will accept objects up to 40mm high as standard, but special versions can be made to accept larger objects. Table Top UV Dryers are used in the PCB and membrane switching industries, for 3D items, as well as conventional graphics, and are equally at home in full production situations and test laboratories. An optional stand is available, with storage shelf and castors.

Table Top UV Dryer Features
• Compact unit
• Quartz infra red filter
• Ammeter/hour meter
• Ozone free lamps
• Lamp height adjustment
• Optional stand
• Available in 2 sizes

UV Curing Kits
UV Curing Kits are available to fit into existing production machinery including web systems. These kits can be made to fit into restricted spaces, with multiples of lamps, heat filters, supplementary reflectors etc. Control systems can be designed to operate with ink drying, adhesive curing or paint application. Custom designed UV is available from Natgraph to operate in a wide range of applications.

Specifications:
UV Bridges & UV Bridging Modules

Please leave your enquiry here, we will reply as soon as possible.
Name*  
Company Name  
Product Interested  
Quantity  
Email*  
Contact No.*  
Ship to Name  
Shipping Address  
Messages*  
   

Switch to Mobile Version
Subscribe Newsletter